在了解直線電機模組地方，我們可以先知道直線電機模組的安裝事項，有哪些需要注意的。

　　一、絕緣電阻檢查

　　使用直線電機模組前，請務必準確測量電磁線圈和絕緣電阻。在直線電機模塊制造商中，測量每個線圈與直線電機電磁線圈外殼之間的絕緣電阻。可使用絕緣電阻計（500vdc）。判斷直線電機的基準如下：

　　絕緣電阻為100米及以下，直線電機一般絕緣，電阻在10米至100米之間，電磁線圈必須按時檢查，絕緣電阻小于10米，請更換新的直線電機。

　　二、直線電機模塊廠家移動子板安裝

　　1. 帶轉子盤的直線電機的表層（機床側）精度要求A.直線電機的機械表面層粗糙度和移動副基板表面層彎曲度在50 m以內。

　　B.轉子板在外力或機械直線電機沖擊等因素作用下可能發生彎曲變形。這種變形不能超過0.1毫米。如果形狀變量大于0.1mm,移動板上的樹脂層可能會開裂。

　　2. 要求動態基片中心與磁鐵定子的重合精度

　　當移動基板的直線電機模塊制造商放置在工作臺上時，直線電機必須安裝在導軌上。此時，轉子基片與磁鐵定子線性電機匹配精度高。

　　三、直線電機模組廠家定子板安裝分析

　　1. 安裝磁鐵定子時注意以下因素：

　　（1）固定螺絲孔的距離；（2）固定螺孔的距離小；（3）磁性定子之間的氣隙。

　　2. 磁性定子安裝精度

　　（1）安裝磁電機定子表面層（機床表面層）。機床表面粗糙度和波動不得超過50um.

　　（2）無需將磁鐵電機定子安裝在變形超過0.1mm的機械表面上。因為通電后，電機轉子板的磁性線圈反復運動，會導致磁性板反復變形，導致磁體表面的環氧樹脂脫落。